Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:ref:engctl50a [2019/12/23 04:35] – [Daytona Twin Tec - TC88A Factory Ignition Maps] ixl2relaxtechtalk:ref:engctl50a [2020/01/29 22:49] (current) – [REF: Engine Control - Sub-50a] ixl2relax
Line 1: Line 1:
 [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]] [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
-====== REF: Engine Control 50a ======+====== REF: Engine Control - Sub-50A ======
  
 \\ \\
  
  
-<font 24px/Arial, , ;;#ffff80;;#000080>☚———————————— USER BEWARE! ————————————☛</font>+<font 24px/Arial, , ;;#ffff80;;#000080>☚———————————— USERS BE AWARE! ————————————☛</font>
  
-There is **NO WARRANT OF USABILITY** for the MAP Files that are made available on the Sportsterpedia. These are being hosted for evaluation\\ +Use these maps at your own risk because there is **NO WARRANT OF USABILITY** for the MAP Files that are made available on the Sportsterpedia.\\ These are being hosted for evaluation by individual users and **ALL USERS MUST MAKE THEIR OWN EVALUATION** 
-by individual users and **ALL USERS MUST MAKE THEIR OWN EVALUATION** of the suitability of using these MAP Files for their intended\\ +of the suitability of using these\\ MAP Files for their intended engine configuration!\\ 
-engine configuration!+\\ 
 +Others have benefited from using some of these maps for their particular engine configuration. However, every engine is different and an incorrect\\ map can create engine damage. If you have been advised by the supplier of your engine parts to use a particular map, it makes sense to follow\\ their recommendation, especially during the break-in period. If you later wish to change to some other ignition map, it still makes sense to seek\\ their advice to learn of any concerns they might have for you to consider.
  
-<font 24px/Arial, , ;;#ffff80;;#000080>☚———————————— USER BEWARE! ————————————☛</font>+<font 24px/Arial, , ;;#ffff80;;#000080>☚———————————— USERS BE AWARE! ————————————☛</font>
  
  
Line 19: Line 20:
 ===== Daytona Twin Tec - TC88A Factory Ignition Maps ===== ===== Daytona Twin Tec - TC88A Factory Ignition Maps =====
  
-This section was created from files supplied by XLForum member, npaisnel. He created these usable files by tediously accessing each and every pre-programmed map. Thank you.+This section was created from files supplied by XLForum member, **npaisnel**. He created these usable files\\ 
 +by tediously accessing each and every pre-programmed map and saving the resulting files. Much thanks.
  
 \\ \\
  
-**Instructions for using the ZIPPED files:**\\ +Here is a Graphic Grid of all the Factory Maps selectable from the dials (click the grid for a larger version image): 
-1) Click the selected ZIP filename and download (save) it to a convenient directory on your local computer.\\ + 
-2) Then UNZIP the file to obtain the Map Image '-m.jpg', the Table Data '-t.jpg' and the usable '.tbl' data file.\\ +{{:techtalk:ref:engctl:tc88a-factory-maps:tc88a-factory-maps-grid-small.jpg?800|}}
-3) Load that '.tbl' data file into the Daytona Twin Tec PC-Link Software to map your ignition module.\\+
  
-\\ 
 \\ \\
  
 +We have made these files available for download, to examine or modify, however you think best.
  
-Here is a Graphic Grid of all the Factory Maps selectable from the dials:+You can select one of the numbers in the grid below that represents the files associated with the equivalent map displayed above.\\ 
 +Each selection represents a map grid position - vertical & horizontal - which is equivalent to the dials on the module.\\
  
-{{:techtalk:ref:engctl:tc88a-factory-maps:tc88a-factory-maps-grid-small.jpg?800|}}+**Instructions for using the ZIPPED files:**\\ 
 +1) Click the selected grid number. These number pairs represent the INITIAL TIMING & SLOPE DIALS on the module.\\ 
 +2) Download (save) it to a convenient directory on your local computer.\\ 
 +3) UNZIP the file to obtain the Map Image '-m.jpg', the Table Data '-t.jpg' and the usable '.tbl' data file.\\ 
 +4) Load that '.tbl' data file into the Daytona Twin Tec PC-Link Software to modify it for your ignition module.\\
  
 \\ \\
- 
-You can select one of the numbers in the grid below that represents the files associated with the maps displayed above.\\ 
-Each selection represents a map position - vertical-horizontal position - which is equivalent to the dials on the module.\\ 
  
 {{:common:space100x5px.jpg|}} {{:common:space100x5px.jpg|}}
Line 163: Line 166:
  
 \\ \\
- 
- 
- 
  
  

Trace: