Differences
This shows you the differences between two versions of the page.
| techtalk:ih:general01 [2017/03/22 04:35] – created hippysmack | techtalk:ih:general01 [2017/04/29 05:57] (current) – hippysmack | ||
|---|---|---|---|
| Line 231: | Line 231: | ||
| |DC-7|#53 (.0595)|#69 (.0293)|- (.070)|3/ | |DC-7|#53 (.0595)|#69 (.0293)|- (.070)|3/ | ||
| - | |||
| - | |||
| - | ====== 1957 - 1969 Sportster Transmission Specifications ====== | ||
| - | =======1957 - 1969 Sportster Transmission Specifications======= | ||
| - | =====Clutch===== | ||
| - | *Type: Dry - Multiple disc | ||
| - | * Capacity: 1900 in-lbs. | ||
| - | * Set up Spring Pressure: 150 lbs. | ||
| - | * Spring adjustment: 3/16 in. from inner surface of spring tension adjusting plate to outer surface of spring cup flange | ||
| - | * Clutch bearing: .0005 - .002 in. loose | ||
| - | * Clutch cover: Must be leak proof. No gasket sealer | ||
| - | * Clutch release rod movement | ||
| - | * 1970: .095 - .115 in. | ||
| - | |||
| - | =====Chain===== | ||
| - | *Type primary: 3/8 in. pitch triple chain | ||
| - | *Looseness: 5/8 to 7/8 in. slack (cold engine) - 3/8 to 5/8 in. slack (hot engine) | ||
| - | |||
| - | =====Starter===== | ||
| - | * Minimum clearance between clutch teeth on starter clutch gear and clutch with starter in up position: .040 in. | ||
| - | * Crankshaft endplay: .001 - .007 in. | ||
| - | |||
| - | =====Mainshaft Group===== | ||
| - | *Clutch gear ball bearing in case: .0001 - .0012 in loose | ||
| - | *Ball bearing on clutch gear: .0001 in. loose - .0009 in. tight | ||
| - | *Clutch gear on mainshaft: .001 - .002 in. loose | ||
| - | *Mainshaft right side roller bearing: .0006 - .0014 in. loose | ||
| - | *Mainshaft end play: .004 - .009 in. | ||
| - | *Third gear | ||
| - | * On shaft: .002 - .003 in. loose | ||
| - | * End play: .015 - .025 in. loose | ||
| - | |||
| - | =====Countershaft Group===== | ||
| - | *Countershaft end bearings: Retained needle roller bearing | ||
| - | *Bearing fit on shaft ends: .0005 - .002 in. loose | ||
| - | *Bearing fit in case: press | ||
| - | *End play: .004 - .009 in. | ||
| - | *Second gear | ||
| - | * On shaft: .001 - .0025 in. loose | ||
| - | * Low gear | ||
| - | * On shaft: .0005 - .0016 in. loose | ||
| - | * End play: .004 - .009 in. | ||
| - | * Drive gear | ||
| - | * On shaft: .001 - .0025 in. loose | ||
| - | * End play: .004 - .009 in. | ||
| - | * Clearance between clutch faces | ||
| - | * Countershaft low an third gear: .039 - .059 in. | ||
| - | * Countershaft second and third gear: .038 - .059 in | ||
