Differences

This shows you the differences between two versions of the page.

--- techtalk:evo:engmech04 [2022/10/10 15:38] – [Rocker Box Gaskets] hippysmack
+++ techtalk:evo:engmech04 [2025/10/01 04:49] (current) – [Pushrods] hippysmack
@@ Line 3: / Line 3: @@
 ====== Rocker Box ======
 ===== Sub Documents =====
   * [[techtalk:evo:engmech04a|Removing the Rocker Boxes]]
   * [[techtalk:evo:engmech04b|Rocker Box Inspection and Servicing]]
@@ Line 10: / Line 9: @@
   * [[techtalk:evo:engmech04j|Rocker Arm Inspection and Servicing]]
   * [[techtalk:evo:engmech04l|Stabilizing Noisy Rocker Arm Shafts]]
+  * [[techtalk:evo:engmech04p|Pushrod Length and Valve Train Geometry]]
   * [[techtalk:evo:engmech04q|Removing / Installing Pushrods and Tubes]]
   * [[techtalk:evo:engmech04s|Top End Oiling]]
-===== Rocker Box Part Numbers =====
+===== Rocker Box Part Numbers =====
 ^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&840|}}|||||||
 |  1986-Up Sportster Rocker Box Part Numbers \\ (Note: an asterisk (*) next to a number indicates that part number is an updated version and not the original part number)  |||||||
@@ Line 67: / Line 67: @@
 |2015-2016 883R, 883NN, \\ 1200CP, 1200CA, 1200CB|17598-07A|  |  N/A  ||17655-05|  |
 |  Notes:|Silver powder coated bottom, black powder coated top.||||||
 ===== Rocker Box Gaskets =====
@@ Line 99: / Line 98: @@
 |:::|:::|(R) 26011-04|:::|:::|
 |2007-Present|Upper (cover gasket)|17362-07 \\ 17362-07B \\ 17362-07C|Does not include cutouts for the breather valve. \\ 17393-07 breather seal required. \\ -07, thin orange rubber. \\ -07A, thin orange crush dimpled rubber.\\ -07B, thin black rubber. \\ -07C, thin crush dimpled black rubber.| |
-|:::|Inner (bottom section)|17695-07 \\ 17695-07A \\ 17695-07B \\ 17695-07C|-07 thin orange rubber, top of bottom section. \\ -07A, orange rubber with crush dimples. \\ -07B, thin black rubber, \\ -07C, thin black rubber with crush dimples.| \\ {{ :techtalk:evo:engmech:2007-up_sportster_inner_rocker_box_gasket_17695-07a_by_mg000000.jpg?linkonly |-07A}} ((photo courtesy of Royal Motorworks Citroen Parts Plus, [[https://www.ebay.com/str/royalmotorworkscitroenpartsplus?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) \\ \\ {{ :techtalk:evo:engmech:2007-up_sportster_rocker_box_inner_cover_gasket_17695-07c_by_1rosesofwood.jpg?linkonly |-07C}} ((photo courtesy of Ebay seller,1rosesofwood, [[https://www.ebay.com/str/rosesofwood?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] ))|
+|:::|Inner (bottom section)|17695-07 \\ 17695-07A \\ 17695-07B \\ 17695-07C|-07 thin orange rubber, top of bottom section. \\ -07A, orange rubber with crush dimples. \\ -07B, thin black rubber, \\ -07C, thin black rubber with crush dimples.| \\ {{ :techtalk:evo:engmech:2007-up_sportster_inner_rocker_box_gasket_17695-07a_by_mg000000.jpg?linkonly |-07A}} ((photo courtesy of Royal Motorworks Citroen Parts Plus, [[https://www.ebay.com/str/royalmotorworkscitroenpartsplus?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) \\ {{ :techtalk:evo:engmech:2007-up_sportster_rocker_cover_inner_gasket_17695-07b_by_on_any_sunday_1961.jpg?linkonly |-07B}} ((photo courtesy of
+Vintage Acquisitions, [[https://www.ebay.com/str/onanysunday1961?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) \\ {{ :techtalk:evo:engmech:2007-up_sportster_rocker_box_inner_cover_gasket_17695-07c_by_1rosesofwood.jpg?linkonly |-07C}} ((photo courtesy of Ebay seller,1rosesofwood, [[https://www.ebay.com/str/rosesofwood?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] ))|
 |:::|Head (bottom section)|16800-84A|One piece gasket between lower box and head.|  |
 |:::|Breather valves \\ (plastic units)|(F) 26012-07|Not a gasket but rather a breather valve. \\ Good maintenance to replace when cover is off. \\ Directional and cannot be installed backwards. \\ Same breather units as 04-06, seal included.|See \\ [[techtalk:evo:engmech07|Breather page]]|
@@ Line 106: / Line 106: @@
 ====== Pushrods ======
-Pushrod lean angle on 91-up engines.
-The lifters are square to the lifter bore but they're not quite square to the rocker arm slot for the pushrod. \\
-There is a slight lean angle between the lifters and the rocker arms as shown below. \\
-The pushrod tubes line up square with the lifter blocks and hide the lean angle of the pushrods. \\
-In the pics below, a inside bore gauge is lined up app. straight from the lifter bore to the rocker arm slot for the pushrod. \\
-This is the app. lean angle of the pushrods between the lifter and the rocker arm. \\
-The pushrod angle also changes as the rocker arm moves thru it's arc while the valve is opened and closed. ((Tomcatt of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074861&page=3)) \\
-{{:techtalk:evo:engmech:pushrod_lean_angle_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:engmech:pushrod_lean_angle_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\